Diy Oversize Biopellets Reactor

[TORX]

I am thinking about going back to pellets, but the amount of pellets I use I fill most reactors when they are running. I sold the best reactor I had used a while ago and regret it, but even it was hard to get it to tumble without getting it stuck to the output. PITA.

So I had an old leaky calcium reactor sitting around and thus beast will hold a lot of pellets AND should never have any issues. I used a 1/2" nipped and carved it for the input nozzle. Now I need to find some acrylic cement to assemble. I have solvent, but will need the cement for the input as it isn't perfect.

Sent from my SM-G925W8 using Tapatalk

 

[Cliff]

Are you going to make it a recirculating reactor?

 

[TORX]

Are you going to make it a recirculating reactor?

I hadn't thought about that, but it is a great idea actually.

Sent from my SM-G925W8 using Tapatalk

 

[AdInfinitum]

FWIW, I found that tall and thin worked far better than short and wide and cone bottoms work well...

 

[TORX]

I agree. I am working with what I have on hand. Although I think i messed it up. I went for a swirl to tumble like my last reactor, but I would prefer the down flow. I ordered some uniseal bulkheads and am going to redo it to resemble a recirculating reactor.

Sent from my SM-G925W8 using Tapatalk

 

[bluewater]

Ever try thickening solvent with acrylic 'sawdust' ?

cheers

 

[TORX]

Ever try thickening solvent with acrylic 'sawdust' ?

cheers

I haven't, but could be a good idea.

Sent from my SM-G925W8 using Tapatalk

 

[TORX]

Redid it. I will be sticking to the down flow set up. Water testing my seals now and all looks good so far.

I have a second to do as well. It is skinnier and taller. Although it is more work as I need to build a top for it.

Sent from my SM-G925W8 using Tapatalk

 

[bluewater]

Redid it. I will be sticking to the down flow set up. Water testing my seals now and all looks good so far.



I have a second to do as well. It is skinnier and taller. Although it is more work as I need to build a top for it.

Sent from my SM-G925W8 using Tapatalk

seen these ? http://www.avastmarine.com/collections/avast-built/products/spyglass... Video shows them working without a top as well. That cone lifts out (no bolts/gaskets) and sure looks like a plastic bottle

cheers

 

[TORX]

seen these ? http://www.avastmarine.com/collections/avast-built/products/spyglass... Video shows them working without a top as well. That cone lifts out (no bolts/gaskets) and sure looks like a plastic bottle

cheers

I love Avast Marine. I did see these and was one of my plans using exactly that...a pop bottle. Still might happen on my seahorse tank lol. MJ400 with a small pop bottle right in the tank.

Sent from my SM-G925W8 using Tapatalk

 

[TORX]

This one is a beast. Here it is with 2 cups of pellets and a mag 9. I still have the feed and drain to set up. But I am a fan. I doubt this bitch will ever clog. I have a smaller lower wattage pump I think i will use though.

Sent from my SM-G925W8 using Tapatalk

 

[TORX]

Sent from my SM-G925W8 using Tapatalk

 

[TORX]

Sent from my SM-G925W8 using Tapatalk

 

[EricTMah]

That thing is a beast!

Sony Xperia Z3

 

[TORX]

That thing is a beast!

Sony Xperia Z3

It has to be. This is with 2 cups. I use approx 4 cups on my system. Maybe more when I am up and running full in 2 months.

Sent from my SM-G925W8 using Tapatalk

 

[TORX]

Up and running, tied into the system. Fired it up the first time and once pressure was added the lid seal leaked like crazy. I took it apart and just used silicone to seal it. No leaks now and working great. I just need to pick up new 1/2" hose to replace the old stuff and move it to the floor. Total out of pocket $25 and a few hours tinkering.

Sent from my SM-G925W8 using Tapatalk

 

[Cliff]

Nice!

 

[TORX]

Any suggestions about bringing the sound of 4 cups of pellets turned down? LoL One reason I am glad my sump is in another room.

Sent from my SM-G925W8 using Tapatalk

 

[heath]

now you are going to have to make one for all of us...lol...

 

[AdInfinitum]

I like....

I was considering doing a cone style but this looks easier and has nice tumble!!